Ever since Apple changed the location of their power input from the top of the iPhone to the bottom, I’ve always been annoyed with this decision. For my day job, I find myself in front of the computer for much of the day. As unhealthy as this may be, it’s what I have to do. Because of this, I’ve always had the tendency to prop my phone on my desk and lean it against the monitor so that I can see any notifications and have instant access to it should I need it. With the change in the input port, I can no longer do this, as the bottom is no longer flat.
As odd as it may seem, it wasn’t until Periscope came out that I found myself even more annoyed that I couldn’t easily prop my iPhone upright…until now, that is! I’ve created the best iPhone stand one could possibly want—especially if you’re an avid Periscope user.
For those of you who have asked me about which stand I use, I’ve created this blog post here to show you how you can have one for yourself too. Oh, did I mention this stand is free?
iPhone Periscope Stand
I’ve always been a fan for great design, so when I took it upon myself to create an iPhone stand, I knew it had to match the pleasing aesthetics of the iPhone itself. With my stand’s sexy curves and sleek, minimalist design, it’s bound to be a hit amongst Apple fans.
- Weighs a mere 2 grams
- Made with razor thin 1mm tough industrial-strength paper
- Comes in two different colours
- Ideal angle for Periscope viewing and broadcasting
- Discrete cable cover allowing you to charge as you broadcast
- Works in both portrait and landscape mode (future-proofing for when Periscope adds this feature)
Follow these instructions for your very own iPhone Periscope Stand.
What you will need:
- Toilet paper roll
Obtain a toilet paper roll of the colour of your choosing.
Looking at the roll straight on, mark a small tick at the base of the roll. This will act as your centre point, as seen from the profile view. We’ll call this view the Profile Centred View (PCV).
Drawing the cut lines in profile view
From the PCV, go to the right edge of the roll, measure 1cm inward, and 4.5cm upward from the base of the roll, and place a tick mark there with your pencil. Draw a horizontal line from this tick mark to the right edge of the roll, as you see it from the PCV. This 4.5cm height is the ideal height to prevent the cable from bending and possibly breaking internal wires.
From that tick mark, draw a 1cm straight line downward.
From that point, draw a 1cm horizontal line inward. Note, this 1cm will determine how snug you would like your iPhone to fit in the stand. With my current case, the 1cm is a nice fit to keep my iPhone from moving around. If you don’t have a case on your iPhone, a snug fit will be:
- 6.9mm for the iPhone 6
- 7.1mm for the iPhone 6 plus
- 7.6mm for the iPhone 5/5s
From the last point, measure 1.5cm further inward. Then move up all the way to the top of the roll, and place a tick mark.
From this tick mark on top, draw a diagonal line to the last point you marked in Step 5, the depth of your iPhone. This line indicates the angle at which your iPhone will be perched on your stand.
This marks the completion of the profile cut lines as you see from the PCV.
Using scissors, cut along the lines that you drew. When you come to the far right edge of the roll, stop cutting once you hit the edge, as you see it from the PCV. One half of your roll should now be cut.
Cutting the other side of the roll
Still looking from the PCV, turn the roll 90 degrees so that the top of the roll is now facing you. Mirror the cutting point on the bottom half of the roll, on to the top side of the roll and place a small cut to mark its location.
Turn the roll back to PCV. Continuing from the cut you made at the far right edge of the roll in Step 8, cut along straight to the same point on the other side, as you see it from the PCV. This is why the centre mark you created in Step 2 is so important. Now just follow along the profile view cut lines, and as your last step, cut diagonally to the small tick mark you made at the top of the roll in Step 9.
Cutting the cord outlet
Starting from the PCV, turn the roll 90 degrees to the right to face the back of your stand. Make sure your view is now centred from the back of the stand.
The cord cover is 1cm wide, at the base of the roll, at the centre, measure out 0.5cm on either side, and cut 1cm upward.
Congratulations, you now have your very own iPhone Periscope Stand!
When the stand is not in use, it can also act as a cable wrapper so you don’t have cables cluttering your desk.
The iPhone Periscope Stand is also future-proof, as it can also be used in landscape mode, for when this functionality is implemented.
If you like this stand, please feel free to comment below and let me know. If you think you can improve upon it, feel free to let me know as well.